Ultra-low temperature FKM for better sealing life

Teknik Makaleler

In recent years, due to automotive emission regulations, an increasing number of car engines are using Gasoline Direct Injection (GDI) technology. Although GDI can improve fuel efficiency and reduce NOx emissions, the pressure of fuel injected into the combustion chamber is at a much higher level.

An increase in pressure will result in the decrease of molecular free volume, which gives rise to an increase in the glass transition temperature (Tg) of the elastomeric material. The increase in Tg will be at a shift of approximately 1ºC (1.8ºF) for every 52bar (750psi) increase in pressure.

As an elastomeric material under low temperature service conditions approaches the glass transition temperature, it undergoes a phase change from a rubberlike phase to a glassy state, losing its elasticity and its ability to perform under pressure as it becomes more brittle. The most notable incident caused by an O-Ring failure was the space shuttle Challenger disaster of 1986. The O-Ring seals, which were FKM, were not designed to withstand the exceptionally low temperature conditions at the time of the shuttle launch.

The choice of the right elastomer for low temperature sealing applications is important. GMORS conducts extensive research and development on extremely low temperature FKM elastomers based on perfluorinated monomers. However, other requirements like low compression set, lower volume swell, resistance to chemical media and other mechanical properties must also be considered because rubber sealing components are often exposed to temperature, pressure and fluid media that can affect its performance.

As shown in Chart 1 below, we develop material formulations based upon customer requirements in terms of color, hardness and low temperature resistance. Among the properties, lowest temperature resistance can reach TR10: -45°C (-49°F) and hardness of SHORE A 60 ~ 90.

In addition to satisfying the low temperature requirements of our customers, our seals also have excellent resistance to rapid gas decompression (RGD), chemical media and are highly durable. For the oil well market, NORSOK M710 RGD certified compounds V9181AA (-40°C) and V9194AA (-45°C) are highly recommended.


TR10 TR10:  -35˚C (-31˚F) TR10:  -40˚C (-40˚F) TR10:  -45˚C (-49˚F)
GMORS COMPOUND V7084AA V8084AC V8184AA V9084AA V6081AA V7081AA V7581AA V9181AA V7094AA V9194AA
Color ⬤Black ⬤Brown ⬤Black
Hardness, (Shore A) 72 83 83 88 63 73 79 91 71 89.5
Low Temperature Retraction Test , TR10 -35.9˚C -36.2˚C -35.4˚C -36.4˚C -40.6˚C -40.4˚C -40˚C -40˚C -44.5˚C -44.7˚C
NORSOK M-710 and ISO23936-2 RGD Test Certificate X X
(Chart 1)


The application of low temperature resistant seals in the market will become increasingly widespread, especially in the automotive, aerospace and oil well markets. From the development of the rubber material to the design of the mold and the final manufacturing of the product, GMORS focuses on the concept of “One Seal Fits All”. (Table 2)

One Seal Fits
All Design Concept
Long-term Sealing Chemical Compatibility Low Temperature
.Compression set
.CSR ( Compression Stress Relaxation)
.Safeguard
.Ethanol
.Methanol
.Diesel
.Biodiesel
.Ensure safety
.Higher pressures
.Dynamic sealing

(Table 2)


In addition to low temperature resistance, our products can also meet the requirements of sealing applications in fuels containing MeOH/EtOH and in application environments of biomass fuels and other media. (Table 3). At the same time, we take into account product safety and product service lifetime which our users are most concerned about in providing a best sealing solution.

Ultra-low temperature FKM have has improved fuel compression set resistance and low temperature performance

LOW TEMPERATURE FKM has improved fuel compression set resistance and low temperature performance

(Table 3)



推薦文章

GMORS'ta gelişmiş PTFE kaplama işlemi

GMORS, elastomerik contalara yönelik düşük sürtünme için çeşitli çözümler sunar. Olduk... Daha

Country-specific certifications of drinking water products by GMORS

Products, equipment and components that come into contact with drinking water have to be evaluated... Daha

Reliability Design Verification

Reliability can easily be confused with quality. In fact, the two are essentially different. In si... Daha

GMORS low friction solutions

The friction characteristics of rubber parts can be result of many factors, such as the nature fea... Daha

GMORS UL approved compound are used in automotive, electronics and refrigerant related fields

In recent years, due to the booming of electronic and semiconductor technologies, inductors and el... Daha